filler such as if delay slot filler have to put NOP instruction into the
delay slot of microMIPS BEQ or BNE instruction which uses the register $0,
then instead of emitting NOP this instruction is replaced by the corresponding
microMIPS compact branch instruction, i.e. BEQZC or BNEZC.
Differential Revision: http://reviews.llvm.org/D3566
llvm-svn: 222580
Summary:
This is because the FP64A the hardware will redirect 32-bit reads/writes
from/to odd-numbered registers to the upper 32-bits of the corresponding
even register. In effect, simulating FR=0 mode when FR=0 mode is not
available.
Unfortunately, we have to make the decision to avoid mfc1/mtc1 before
register allocation so we currently do this for even registers too.
FPXX has a similar requirement on 32-bit architectures that lack
mfhc1/mthc1 so this patch also handles the affected moves from the FPU for
FPXX too. Moves to the FPU were supported by an earlier commit.
Differential Revision: http://reviews.llvm.org/D4484
llvm-svn: 212938
Summary:
This is similar to r210771 which did the same thing for MTHC1.
Also corrected MTHC1_D32 and MTHC1_D64 which used AFGR64 and FGR64 on the
wrong definitions.
Differential Revision: http://reviews.llvm.org/D4483
llvm-svn: 212936
enabled and mthc1 and dmtc1 are not available (e.g. on MIPS32r1)
This prevents the upper 32-bits of a double precision value from being moved to
the FPU with mtc1 to an odd-numbered FPU register. This is necessary to ensure
that the code generated executes correctly regardless of the current FPU mode.
MIPS32r2 and above continues to use mtc1/mthc1, while MIPS-IV and above continue
to use dmtc1.
Differential Revision: http://reviews.llvm.org/D4465
llvm-svn: 212930
Summary:
RET, and RET_MM have been replaced by a pseudo named PseudoReturn.
In addition a version with a 64-bit GPR named PseudoReturn64 has been
added.
Instruction selection for a return matches RetRA, which is expanded post
register allocation to PseudoReturn/PseudoReturn64. During MipsAsmPrinter,
this PseudoReturn/PseudoReturn64 are emitted as:
- (JALR64 $zero, $rs) on MIPS64r6
- (JALR $zero, $rs) on MIPS32r6
- (JR_MM $rs) on microMIPS
- (JR $rs) otherwise
On MIPS32r6/MIPS64r6, 'jr $rs' is an alias for 'jalr $zero, $rs'. To aid
development and review (specifically, to ensure all cases of jr are
updated), these aliases are temporarily named 'r6.jr' instead of 'jr'.
A follow up patch will change them back to the correct mnemonic.
Added (JALR $zero, $rs) to MipsNaClELFStreamer's definition of an indirect
jump, and removed it from its definition of a call.
Note: I haven't accounted for MIPS64 in MipsNaClELFStreamer since it's
doesn't appear to account for any MIPS64-specifics.
The return instruction created as part of eh_return expansion is now expanded
using expandRetRA() so we use the right return instruction on MIPS32r6/MIPS64r6
('jalr $zero, $rs').
Also, fixed a misuse of isABI_N64() to detect 64-bit wide registers in
expandEhReturn().
Reviewers: jkolek, vmedic, mseaborn, zoran.jovanovic, dsanders
Reviewed By: dsanders
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D4268
llvm-svn: 212604
Summary:
To make this work for both AFGR64 and FGR64 register sets, I've had to make the
instruction definition consistent with the white lie (that it reads the lower
32-bits of the register) when they are generated by expandBuildPairF64().
Corrected the definition of hasMips32r2() and hasMips64r2() to include
MIPS32r6 and MIPS64r6.
Depends on D3956
Reviewers: jkolek, zoran.jovanovic, vmedic
Reviewed By: vmedic
Differential Revision: http://reviews.llvm.org/D3957
llvm-svn: 210771
Summary:
This is a white lie to workaround a widespread bug in the -mfp64
implementation.
The problem is that none of the 32-bit fpu ops mention the fact that they
clobber the upper 32-bits of the 64-bit FPR. This allows MTHC1 to be
scheduled on the wrong side of most 32-bit FPU ops, particularly MTC1.
Fixing that requires a major overhaul of the FPU implementation which can't
be done right now due to time constraints.
The testcase is SingleSource/Benchmarks/Misc/oourafft.c when given
TARGET_CFLAGS='-mips32r2 mfp64 -mmsa'.
Also correct the comment added in r203464 to indicate that two
instructions were affected.
Reviewers: matheusalmeida, jacksprat
Reviewed By: matheusalmeida
Differential Revision: http://llvm-reviews.chandlerc.com/D3029
llvm-svn: 203659
Summary:
This is a white lie to workaround a widespread bug in the -mfp64
implementation.
The problem is that none of the 32-bit fpu ops mention the fact that they
clobber the upper 32-bits of the 64-bit FPR. This allows MFHC1 to be
scheduled on the wrong side of most 32-bit FPU ops. Fixing that requires a
major overhaul of the FPU implementation which can't be done right now due to
time constraints.
MFHC1 is one of two affected instructions. These instructions are the only
FPU instructions that don't read or write the lower 32-bits. We therefore
pretend that it reads the bottom 32-bits to artificially create a dependency and
prevent the scheduler changing the behaviour of the code.
The other instruction is MTHC1 which will be fixed once I've have found a failing
test case for it.
The testcase is test-suite/SingleSource/UnitTests/Vector/simple.c when
given TARGET_CFLAGS="-mips32r2 -mfp64 -mmsa".
Reviewers: jacksprat, matheusalmeida
Reviewed By: jacksprat
Differential Revision: http://llvm-reviews.chandlerc.com/D2966
llvm-svn: 203464
Fixed an inappropriate use of BuildPairF64 when compiling for MIPS32 with FP64
which resulted in an impossible constraint on the register allocation. It now
uses BuildPairF64_64.
llvm-svn: 195007
accumulator instead of its sub-registers, $hi and $lo.
We need this change to prevent a mflo following a mtlo from reading an
unpredictable/undefined value, as shown in the following example:
mult $6, $7 // result of $6 * $7 is written to $lo and $hi.
mflo $2 // read lower 32-bit result from $lo.
mtlo $4 // write to $lo. the content of $hi becomes unpredictable.
mfhi $3 // read higher 32-bit from $hi, which has an unpredictable value.
I don't have a test case for this change that reliably reproduces the problem.
llvm-svn: 192119
precision loads and stores as well as reg+imm double precision loads and stores.
Previously, expansion of loads and stores was done after register allocation,
but now it takes place during legalization. As a result, users will see double
precision stores and loads being emitted to spill and restore 64-bit FP registers.
llvm-svn: 190235
The MSA control registers have been added as reserved registers,
and are only used via ISD::Copy(To|From)Reg. The intrinsics are lowered
into these nodes.
llvm-svn: 189468
point registers. We will need this register class later when we add
definitions for instructions mfhc1 and mthc1. Also, remove sub-register indices
sub_fpeven and sub_fpodd and use sub_lo and sub_hi instead.
llvm-svn: 188842
load/store instructions defined. Previously, we were defining load/store
instructions for each pointer size (32 and 64-bit), but now we need just one
definition.
llvm-svn: 188830
invalid instruction sequence.
Rather than emitting an int-to-FP move instruction and an int-to-FP conversion
instruction during instruction selection, we emit a pseudo instruction which gets
expanded post-RA. Without this change, register allocation can possibly insert a
floating point register move instruction between the two instructions, which is not
valid according to the ISA manual.
mtc1 $f4, $4 # int-to-fp move instruction.
mov.s $f2, $f4 # move contents of $f4 to $f2.
cvt.s.w $f0, $f2 # int-to-fp conversion.
llvm-svn: 182042
This option is used when the user wants to avoid emitting double precision FP
loads and stores. Double precision FP loads and stores are expanded to single
precision instructions after register allocation.
llvm-svn: 181718
register.
- Define pseudo instructions which store or load ccond field of the DSP
control register.
- Emit the pseudos in MipsSEInstrInfo::storeRegToStack and loadRegFromStack.
- Expand the pseudos before callee-scan save.
- Emit instructions RDDSP or WRDSP to copy between ccond field and GPRs.
llvm-svn: 180969
Expand copy instructions between two accumulator registers before callee-saved
scan is done. Handle copies between integer GPR and hi/lo registers in
MipsSEInstrInfo::copyPhysReg. Delete pseudo-copy instructions that are not
needed.
llvm-svn: 180827
This patch initializes t9 to the handler address, but only if the relocation
model is pic. This handles the case where handler to which eh.return jumps
points to the start of the function.
Patch by Sasa Stankovic.
llvm-svn: 178588
physical register $r1 to $r0.
GNU disassembler recognizes an "or" instruction as a "move", and this change
makes the disassembled code easier to read.
Original patch by Reed Kotler.
llvm-svn: 170655
Sooooo many of these had incorrect or strange main module includes.
I have manually inspected all of these, and fixed the main module
include to be the nearest plausible thing I could find. If you own or
care about any of these source files, I encourage you to take some time
and check that these edits were sensible. I can't have broken anything
(I strictly added headers, and reordered them, never removed), but they
may not be the headers you'd really like to identify as containing the
API being implemented.
Many forward declarations and missing includes were added to a header
files to allow them to parse cleanly when included first. The main
module rule does in fact have its merits. =]
llvm-svn: 169131
the temporary register that was used to load the immediate. Currently, it always
returns register $at, but this will change if, in the future, we decide to use
another register.
No changes in functionality.
llvm-svn: 162417
Eric Christopher